- More effective joint movement restraint
- Stainless steel strap bands are 12.5% thicker than on traditional no hub
couplings providing a positive seal when properly torqued to 80 in/lbs
- Stronger, more uniform scaling capacity
- Axially slotted clamp bands tighten independently to accommodate most
any variances in outside diameters of cast iron pipe and fittings being joined
- Greater surface load bearing
- Wider 304 Series stainless steel shield accommodates additional sealing
clamps to provide for greater load bearing contact
1-1/2" - 4" sizes: Four stainless steel bands
5" - 15" sizes: Six stainless steel bands
- Higher resistance to shear forces
- Rugged construction, excellent sealing properties and the arrangement
of intermittent corrugations in the outer stainless steel band provide
resistance to shear forces and help alignment while maintaining flexibility
- Corrosion resistant
- 304 Series stainless steel combined with significant deflection factor makes
this coupling highly dependable above and below ground
- Safe and easy to install
- Flanged gasket helps maintain alignment during installation and tapered ends
on shield reduce friction and prevent injury from sharp edges
- Versatile
- Internal profile of elastomeric sleeve against intermittent corrugation
suits specific performance application of non-potable waste systems
|
|
HeavyWeight Couplings
|
| Test |
Gasket Physical Tests |
ASTM |
| Tensile Strength |
1500 PSI min. |
D412 |
| Elongation |
250% |
D412 |
| Durometer (Shore A) |
70±5 |
D2240 |
| Accelerated Aging |
15% max. tensile and 20% max. elongation
deterioration.10 pts. max. increase in hardness.
All determinations after oven aging for 96 hrs. at 158°F. |
D573 |
| Compression Set |
15% max. after 22 hrs. at 158°F |
D395 |
| Oil Immersion |
80% max. volume change after immersion in TRM
oil #3 for 70 hrs. at 212°F. |
D471 |
| Ozone Cracking |
No visible cracking at 2X magnification of the gasket after 100 hrs.
exposure in 1.5 PPM ozone concentration at 100°F testing and
inspection to be on gasket which is loop-mounted to give
approx. 20% elongation of outer surface. |
|
| Tear Resistance |
Die C 150 lbs. max/inch of thickness |
D624 |
| Water Absorption |
20% max. by weight after 7 days at 158°F |
D471 |
|
|
Specifications:
- Multiple bands attached to heavy duty, corrugated 304
Series stainless steel shield over a molded
one-piece elastomer sealing sleeve
- Sealing rings on flanged neoprene rubber gasket
meet or exceed the requirements of ASTM C 564
- Axially slotted heavy duty worm drive clamps tightened
to 80 in/lbs of torque
- FM 1680 compliant
|
Gasket Dimensions
|
| B |
W |
| 1-1/2" |
3.0 |
| 2" |
3.0 |
| 3" |
3.0 |
| 4" |
3.0 |
| 5" |
4.0 |
| 6" |
4.0 |
| 8" |
4.0 |
| 10" |
4.0 |
| 12" |
5.5 |
| 15" |
5.5 |
|
| C 150 HW |
1-1/2" |
3.000 |
| C 200 HW |
2" |
3.000 |
| C 215 HW |
2" x 1-1/2" |
3.000 |
| C 300 HW |
3" |
3.000 |
| C 320 HW |
3" x 2" |
3.000 |
| C 400 HW |
4" |
3.000 |
| C 430 HW |
4" x 3" |
3.000 |
| C 500 HW |
5" |
4.000 |
| C 600 HW |
6" |
4.000 |
| C 800 HW |
8" |
4.000 |
| C 1000 HW |
10" |
4.000 |
| C 1200 HW |
12" |
5.500" |
| C 1500 HW |
15" |
5.500" |
|
